How to Change Engine Oil in Motorcycle: A Complete Guide
If you own a motorcycle, you know how important it is to keep your engine oil fresh and clean. Engine oil lubricates, cools and protects your engine’s internal parts from wear and tear. Changing your engine oil regularly is one of the easiest and most effective ways to maintain your motorcycle’s performance and longevity.
But how do you change your engine oil yourself? Is it difficult or complicated? What tools and materials do you need? How often should you do it? In this blog post, we will answer all these questions and more. We will show you how to change your engine oil in motorcycle in 5 easy steps, with tips and tricks along the way. Let’s get started!
In short:
1. Get tools and engine oil
2. Open drain plug
3. Drain engine oil
4. Change oil filter
5. Close drain plug, pour engine oil.
Step 1: Gather Your Tools and Materials
Before you start changing your engine oil, you need to gather some tools and materials. Here is a list of what you will need:
- New engine oil. Refer to your owner’s manual for the recommended type and weight of oil for your motorcycle. You can also use synthetic engine oil for better performance and efficiency. Don’t know what Engine Oil is best for your bike? Get in touch with Automarvels Expert. Buy the best Engine oil for your bike at automarvels.com
- New oil filter. You should replace your oil filter every time you change your engine oil, as it helps remove dirt and debris from the oil.
- Tool set. You will need a wrench or socket (usually 17 mm) to remove the drain plug and the oil filter cap, as well as a screwdriver or pliers to loosen the hose clamps if your motorcycle has an external oil filter.
- Drain pan. You will need a large container to catch the used oil as it drains out of the engine.
- Funnel. You will need a funnel to pour the new oil into the engine without spilling.
- Some old rags (dirty cloth). You will need some rags to wipe off any excess oil or dirt from the engine parts.
- Service manual for your bike. You should always consult your service manual for specific instructions and specifications for your motorcycle model.
Step 2: Warm Up Your Motorcycle and Drain the Used Oil
Before you drain the used oil from your engine, you should warm up your motorcycle for a few minutes. This will make the oil thinner and easier to drain. However, don’t let your motorcycle get too hot, as you might burn yourself with the hot oil. Give it 10 or 15 minutes to cool down after warming up.
Next, place your motorcycle on a center stand or a rear paddock stand if you have one. This will make it easier to access the bottom of the engine. If you don’t have a stand, you can do it on the side stand, but make sure your motorcycle is stable and level.
Then, place the drain pan under the drain plug, which is usually located at the bottom of the engine case. Use a wrench or socket to unscrew the drain plug carefully and slowly, and let the oil flow out into the pan. Be careful not to drop the drain plug into the pan or lose the washer that goes with it.
While the oil is draining, you can also remove the oil filter cap, which is usually located on the side of the engine case. Use a wrench or socket to unscrew it and pull out the old oil filter. Some motorcycles have an external oil filter that is connected by hoses to the engine case. In that case, you will need to loosen the hose clamps with a screwdriver or pliers and disconnect the hoses from the filter.
Step 3: Replace the Oil Filter and Reinstall the Drain Plug
Once all the oil has drained out of the engine, you can replace the old oil filter with a new one. First, pour some fresh engine oil on the new filter and rub it around with your fingers. This will help create a good seal between the filter and the engine case.
Then, insert the new filter into the filter cap and screw it back onto the engine case. Make sure it is tight but not over-tightened. If your motorcycle has an external oil filter, reconnect the hoses to it and tighten the hose clamps.
Next, reinstall the drain plug with its washer onto the bottom of the engine case. Again, make sure it is tight but not over-tightened. You don’t want any leaks or stripped threads.
Step 4: Pour in New Engine Oil
Now that you have replaced the oil filter and reinstalled the drain plug, you can pour in new engine oil into your engine. First, check your service manual for how much oil your motorcycle needs. Usually, there is a dipstick or a sight glass on the side of the engine case that shows you how much oil is in there.
Then, pour the required oil using a funnel. Keep an eye on sight glass. Or try to get the oil in a measure and pour it into the engine. Usually, the required oil is mentioned on engine case. If not, check with your user manual or service manual. If you are not sure what oil is best for your motorcycle and quantity, chat with our expert on whatsapp.
Pour additives for optimum performance of your bike and frictionless operation.
Congratulations, You’re done. Now start the engine for few minutes, don’t over rev the engine. Shut it down, or start riding and feel the difference.